After the power is turned on, there is no “drop†called?
1. Check if the power supply output voltage is normal. If not, replace the power supply.
2. Check if the power supply is properly connected to the host. If not, reconnect the power supply;
The switch door is not continuous and smooth, and there is jitter?
1. Check whether the power load can drive the electronic lock and the motor, if not, replace the power supply;
2. Check the thickness of the connecting line between the power output line and the input line of the door opener. If the line is thin, replace the thick line (you cannot use the network cable);
3. After the power is cut off, confirm that the door body can be smoothly pushed by hand without obvious resistance. If there is obvious resistance, please re-adjust the installation position of the door opener;
4. Power on, please increase the resistance sensitivity F9 or decrease the opening speed and closing speed;
After the door is opened, the door keeps shaking?
Whether the green function line (on/off button line) is connected to the chassis (or the common terminal) for a long time. If the door shake phenomenon is inevitable, please disconnect it;
The remote control is not working?
1. Confirm that there is a battery in the remote control and the battery is fully charged. If there is any problem, please change the battery;
2, let the remote control leave the door machine far away, and then remote control;
3, open the cover according to the remote control learning process to re-learn the remote control;
Can the electronic lock not be locked or unlocked smoothly?
1. Confirm that the electronic lock is the same as the system setting lock. If it is different, please adjust the lock type.
2. If the door cannot be locked: if the door is not in place, please turn up the locking force of the door or turn the door buffer down or turn the door closer to the door, so that the door can be closed smoothly;
3. If the door cannot be unlocked: Please turn the unlocking time to increase the opening time, and give the electronic lock enough time to disengage;
4. Confirm whether the electronic lock is damaged. If it is faulty, please change the electronic lock with good function;
The door can't always open to the setting angle?
1. Horizontal movement adjusts the relative position of the door opener and the door shaft;
2. Please reset the output shaft rotation angle;
Cannot close automatically after opening the door
1. Confirm whether it works in the normally open mode. If yes, please switch to the very open mode.
2. Confirm whether there are signals in the two green channel ports, and if so, cancel the signal;
If the door switch is irregular, please reset the starting point and opening direction. If it cannot be solved, please consult the manufacturer;
Warning
1. Attention! Follow the instructions carefully, which is very important for personal safety. Incorrect installation or misuse of the product may cause serious damage to people and property;
2. Please read the instructions carefully before installing the product;
3. Save the instructions for future use;
4. Do not install this product in areas with explosion hazards; flammable gases are serious safety hazards;
5. Mechanical parts must comply with relevant national standards;
6. The installation must comply with the relevant national regulations;
7. The power should be cut off before the system is overhauled;
8. Check that the grounding system is correct;
9. Parts not manufactured by the company are installed in the system. If there is a safety problem and it is not working properly, the company is not responsible;
10. Repair only the original part;
11. Do not make any changes to the components of the system;
12. The installer must provide the user with detailed instructions on the operating methods and emergency conditions, and provide the product description to the user;
13. Children and other unrelated persons are strictly prohibited from approaching when installing the product;
14. Place the remote control out of the reach of children to prevent accidents;
15. It is strictly forbidden for users to try to repair or adjust the system by themselves.
16. Nothing specified in the manual is not allowed;
Prospecting Core Drilling Rig
Core Hole Drilling is a drilling technique whereby an oil or gas well is drilled either in a vertical hole or horizontal hole. The method used to drill a vertical hole is known as vertical drilling whereas for a horizontally drilled hole is known as horizontal drilling.
The core drill rig of full hydraulic and rotor adopted the technology of wire-line coring has been the dominant type rig for solid mineral deposits prospecting in developed counties of the world. The rig is light, simple in structure, and easy for transportation. The mast has the functions of sliding and touching ground, the spindle lifted and lowered with hydraulic cylinder. It could be folded for transport and relocation. The spindle hole is in large diameter.
It is a thoroughly new-type wire-line Core Drilling Rig developed on the basis of the market demand and the advanced techniques in the world. It is mainly used for metal&nonmetal solid exploration and exploration of coal-bed methane, nature gas mining, hydrogeology well drilling, geothermal well drilling, mining gallery, ventilation and drainage of exploratory and emergency construction projects.
In most cases, it can drill into stratums with depths of more than 350 meters and more than 500 meters and can be widely used in core drilling work with extremely complex ground conditions.
It is ideal equipment for deep-hole geological exploration drilling. Contact us to get a cheap YK core drilling machine price.